Jump to content

ikb

Members
  • Posts

    305
  • Joined

  • Last visited

Everything posted by ikb
 
 
  1. Which side of the road do they drive on in the Boro??
  2. ikb

    Gg Heavy Clutch

    I would give Kev at GasGas UK a ring, or maybe the slave cylinder seals have swelled making its operation stiff??? I had an 06 250 and the clutch was fine so you shouldnt need different master cylinders or hoses. Ian
  3. ikb

    Rusty Main Bearings

    Ive got an 08 Beta with rusty mains!! I always run for a while after washing, obviously not long enough!!! I was wondering which 2 stroke oil you use? I have been using Ipone strawberry flavour stuff which is a tenuous link to Sherco as Ipone is the recomended oil for Shercos Ian
  4. ikb

    Main Bearings Gone

    Guess what...my 08 250 is sounding very swishy Again a bike with careful owners!!!!!!
  5. Check the flow from the petrol tap, Ive heard that some times the gasket get miss aligned. And check the filter in the carb, and the float hieght. Ian
  6. Never saw any!!! In Yorkshire its only counts as snow if its more than a foot deep
  7. If you warm the bike up then let it stand for 10 mins with the engine stopped the heat works its way to the carb (as there is no cold air going through it). it helps a bit as well
  8. Thats no defeat! Nick rode the girlie course!!!
  9. Over t hill at the Richmond Club Boxing day Trial.... 33 Betas 33 GasGases 41 Shercos 22 Monts 9 Scorpas Hard course tied Sherco and GasGas Middle Beta Easy GasGas Discuss!!
  10. Yes it is the pickup for the speedo
  11. ikb

    Hebo Pegs On A Rev3

    Hi, Just fitted some Hebo pegs to my 08 250 and looking side on they are sloping down at the front! probably about 5 degrees although it doesnt sound much you can feel that youre riding on the back edge of the pegs a bit. I will see how they feel tomorrow I have compared them to the original Beta pegs and there is a difference in the angle of the bracket and I was wondering if anyone else has noticed this? or can you buy pegs with different angled brackets???
  12. ikb

    2009 Bikes

    How did you know? Do you have an inside contact?
  13. And guess what Ebay is good for bolts!!! there are loads of Ebay shops selling both stainless and high tensile in most forms!! As I work as an engineer in the pharmaceutical industry I dont buy many!
  14. Hi, I have only had them in for a few days, the clutch is lighter and seems to work OK. I will know better after the weekend!!! Ian
  15. Dan, I have sent you a PM. Ian
  16. The standard spring cap is just a flat washer so the top of the spring is level with the top of the posts in the clutch centre basket, my caps are stepped so the springs are compressed 3mm less so they have less pre load making the clutch lighter. I think this makes sense at this late hour!!! Simpley the springs arent squashed as mutch!!! IKB
  17. Having read the above, I have made some new spring caps that act as 3mm (0.120 inch) shims on the springs. I now have a lighter cluch that even looks better!!! (only when in bits though!!). Is there a market for these? so i can make my fortune!!
  18. ikb

    Beta Flywheel Weight?

    Just tried my new (to me) 08 250 today without the flywheel weight, it seems quite a bit livelier more like my old Gasgas 250 (with a weight on!). As the bike is sold with the weight fitted is it part of the whole package of a well balanced controllable bike with good traction? Should we be tampering with a good proven setup just because it feels better, or more like what I was used to?
  19. Snap, I have just done the same! It looks good but I have yet to ride it in anger!!
  20. Looks just like my vice!!! Mine must be about 30 years old and not cracked yet!!!
  21. ikb

    Just Got A Rev3 250!

    Just got a mint 08 250!! I hope I like it as much as my last 2 GasGas's!!! Ant tips? Its done about 6 easy trials and is as new!! I hope JLI are as good as Shirty as his service is 100% or perhaps I wont need anything?!?!
  22. I compete for fun!!! May as well go to an event as its just as easy as going practicing
  23. Here goes Back suspension either too harsh or too bouncy Hard work over the moors (I some times wonder if my shock was faulty) Engine a bit agricultural easy to damage clutch covers Gear ratios just too wide in 4th n 5th for flying over the moors Clutch was a bit savage But reliable but not brilliant to work on. I just found it hard work to ride on long Trials Much happier on a 06 Gasgas but they do need looking after but are easy to work on (much practiced!!)
  24. Hated my SY250, went back to GasGas much happier! so as you see its all down to personal preference!!!
  25. ikb

    Observers

    I seem to remember you can be given a 10 for arguing with an official
 
×
  • Create New...