Honda

Hi there Got a TLM 50 for my son, and was after a big bore kit. I cant find anything TLM specific, but can find an MT50 60cc kit below - apparently the same engine ? Can anyone confirm before I buy ? http://www.patternparts.net/fcm-Barrel__Big_Bore_Kits-Honda_MT_50-18-69.aspx cheers John

Hi, is there anyone here who has a TLM50 and could measure the port durations for me? what i need is the distance from the top of the exhaust port and transfer ports to the top of the cilinder. thanks in advance.

Fouled a plug in every ride last three rides and 3 plugs today! Bike starts well after new plug and runs great. I can rev through the whole range without hesitation and does not lack power! When I shut the bike off, it wont start very easy. Like 3 to 4 kicks and then it might start or just foul again. Running the stock plug cr6eh9 Notes: Plug is always extremely dry with black sutt adjusted valves recently but it did not resolve issue. Found considerable amount of engine oil today in the air box. Supposedly normal? Before this all started, I was riding one day and when I tried shut off, bike kept running even though the lanyard was …

Can someone clarify how to install the front sprocket retention hardware for a TL250?. There is a flat washer with cut outs to slide on the spline. There is a second washer with similar cutouts which also has some horizontal protrusions that will mate with the first washer. However, I don't see how these two washers can mate once on the spline. Then there is an e ring that fits but is not a tight fit in the groove on the spline.

Just for fun I thought I would start a thread and get opinions on both bikes! I really like them both and have one of the two and possibly could get the other one! . I'm also looking for a set of piston rings for the stock Honda TLM piston.....

I bought a new chain and sprocket kit for for my TL250 but no spacer was available for the rear sprocket. I can make one but am seeing only two ways, neither of which is highly desirable. See picture 1. -If I mount spacer to hub and then sprocket to spacer, I will have to open up holes in the freshly anodized sprocket for nut clearance for the spacer to hub attachment. -IF I could find longer studs, I could use them and basically sandwich a spacer between sprocket and hub. However, I suspect that studs that have been in place for 1/2 century will not come out easily. What have others done? Pictures? The sprocket is supposed to be a TL125 sprocket but …

Hi all, Anyone have any experience / advice to share on adding flywheel weight to small four-strokes for trials..?

Hi Anyone know how much fork oil in each leg for a Honda MT125 Elsinore 1974-1976? Thanks

Hi I have got a honda tlm-200. And,I have taken delivery of an immobilised engine as a spare and would like to repair it. i want to find out were can i get parts for my tlm.

Hi I've recently bought a CT 250 SC Silk Road which is almost identical to the CL 250 SC. I have been told the engine is the same as the XL250 and CB 250 RS of the early 80's. Can anyone confirm this and is it the same engine as the TL250? As the CT250Sc is a rare bike in the UK parts are not listed as often as the supposed sister bikes so it would be good to know that I can get parts for the engine based on the other bikes. Its in very good condition with 14k on the clock but the engine smokes which I have been told is likely to be the Valve stem seals or possible a broken ring. Need to start getting some parts soon so any info welcome. Thanks Iain Picture of …

Does anyone have experience with downsizing wheels diameters? I'm considering putting smaller 16" wheels on a honda TLM 50 for my grandson. Most electric trials bikes do have a 16" variant and some other 50cc 2 stroke junior trials bikes had both 16" and full size wheel size options.

THINKING OF USING ONE OF THESE BERLT KITS (eBay number 274422258243) ON A ROCKHOPPER 125J ENGINE, TAYLORS OF NEWCASTLE UPON TYNE BUY THEM THEN RELINE AND MACHINE THE LINER, ALTER CROWN HEIGHT AND FACES BEOFRE SELLING IT FOR £169.50 WITH POST AT £6.90. ITS A CHEAP KIT WITH NO WORK FOR YOU TO DO, THEY DO IT ALL FOR YOU. ITS FOR THE ENGINE WITH THE LARGE 70MM CRANKCASE SPIGOT HOLE, LATE TL's, XL's & ROCKHOPPER - FIELDTRIPPER (JAPANESE IMPORTS) BIKES CAME WITH THIS ENGINE, IT HAS THE SAME SIZE CRANKCASE OEPNING AS THE TLR-XR 200 ENGINES, ITS A STRAIGHT FIT KIT AND YOU CAN USE THE SAME CARB THOUGH THEY DO RECOMMEND A LARGER 28MM MIKUNII CARB, AND THEY WILL SELL YOU IT CHE…

Hi , would anyone here have a 1975 TL 125 stator coil they could part with - wound or unwound - I want to have lights on my TL and can’t find one . If anyone has one or knows where I might find one that would be a huge help . Thanks a lot , Andy

Hi All I just purchased a TLM200 1988 which requires some minor works before I trial ans trail it. I am having problems finding spares, tried the usual CMSL and David Silver etc. Please can anyone point me in the right direction? I am after fork seals, service parts and bodywork if possible. Is the engine and chassis common to other models? Thanks very much. Tim

Anyone know where I can get a tlm rubber manifold from or is there one off another bike that will work, my friends just got a tlm and it is split around where the carb fits, also what keihin carb so we can source a rebuild kit as it seems to be running very rich like the choke is not closing properly. Thanks

Hello, I live in France and I am repairing a Honda TLM250R. I am looking for a PDF file of the workshop manual and the parts list for this bike. Thanks for your help.

Hey there! I had to change the Conrod Kit on my TLM 250´88 recently. As always there were no parts listed anywhere for this model! After disassembling the crankshaft i found out that there is a conrod kit made for Honda NSR 150. Available through different manufacturers like TKRJ, Royal and some others. This Kit has the same length and uses a 24mm conrod pin also. Only the conrod pin is to short for the TLM. So i had to order a TLM 220 pin from cmsl.nl. All these parts were delivered in about a week and looked exactly the same as the original. I believe all TLM models have the same stroke, so i think these parts might fit all models. Please c…

Just had a look at the DVLA website and apparently the TL125 I bought new from Gordon Farley vis still taxed - does someone on here own it now?

Does someone sell a 13 tooth front sprocket for the TL250? I have a 14 and see 12 t for sale but no 13. I have spent some time on the bike now. It works well for such a heavy bike but it is not smooth when rolling on and off the throttle like when snaking slowly through trees with tight turns. There is a lot of engine braking with throttle off and as soon as the slide lifts a surge forward. I went from a very quick MX type throttle to an Amal trials throttle with no real change to this. The engine does not spin up quickly like it needs more flywheel. I'm thinking lower gearing may help in those slow on/ off parts. I have the stock gearing and am thinking lower…

I have a 1986 trl reflex that needs the cylinder bored. What are the options for a piston? Or cylinder replacement. I read something about a Honda generator 67mm piston.