Beta

On my 16 evo the black bits of the wheel rims look all white and milky. I'e noticed it on other not just mine. Anyone know how get them back looking good? Thanks

Does a handle bar mounted map and light switch combo exist for a 2016 beta evo 2t? Or do I need to rig one up from another bike?

Having problems with a 2007 125 cc Rev3. Bike will not start when cold. It acts as though the choke is not functioning. If I give it a shot a starting fluid it will start first kick and once warm will start repeatedly with just one kick and continue to run without any problems. To date the stator has been replaced, crank seals replaced, a carb o-ring kit installed, and the carb (Dellorto) has been off and cleaned at least 4 times, with special attention to the choke circuit. With all that done it still will not start when cold unless I give it a shot of starting fluid first. Would appreciate and thoughts on what to look for.

What stuff should I pack my exhaust with?

I'm going to get a 2006 Beta 125 soon and am just wondering how to keep it nice. My first few rides I'll probably take it really easy but I can imagine after a bit I'll resume my usual riding style (slamming it into rocks). When I first get it I know to give various parts a good smearing of grease but how do I run the engine in properly? I'm also going to give it a couple of sheets of technosel and some fork protectors for cosmetic reasons. I'm really looking forward to buying it as I've worked very hard and saved alll my money and I've never had a new bike before Any help or advise would be greatly appreciated

can anyone help please, i cannot get the brake fluid to bleed through the from the master cylinder to the caliper , i have put a brand new seal kit in and everything is clean and tight , ive bled many hydraulic brakes in my time so not a novice ....but i cant fathom out what is wrong here, other than a possible score in the master cylinder ( which looks fine) is there a special technique that i need to know, the banjo fitting id higher than the fluid level so i cant see how gravity can help cheers Neil

Hi. Does anybody know if Beta do a manual for a 2002 Rev 3. Any help appreciated Cheers

trial is not so common around here within a 4 hour drive radius the only used trialsbike in a bike-#7-price-range other than the Fantic 301 you told me to stay clear off is a 97 Beta Techno I do not want to compete only have fun, improve my trail riding skills and on occassion take the trials bike on a tough trail any opinion from a real trials rider, is the Techno a learners bike? or should I go on looking? if so what should I look for? the TY-S175F sounds like something I'd like to have, but my wallet does not agree with another new bike my question is not what kind f wear and tear to specificly look for when I check the bike that I found in old Beta threa…

Having just been set right on a bike I proposed to buy which was identified by a forum member as being mid-advertised as a 2012 when it was a 2005, can I seek your advice in confirming/not the bike below, which is described as a Beta 250 from 2008, please? I appreciate it isn’t a 4T (presumably the plastics or decals are from another bike) I plan to go to see it Friday, but if it’s a wrong’un, I don’t fancy the two-hour drive… thanks in advance

Being a portly chap and a reasonable clubman and looking for a new trials motorcycle, i have a 250 05 but wonder whether an upgrade to a 270 would help me on my way. I rode a 280 GG an it pulled me arms out. Does any one out there with a 270 have any advice on the power and rideability etc... Many thankenyou's

my fan on my 07 rev 3 just suddenly stoped working. tryed bypassing the switch but still no life. any suggestions would be cool . chears

Hi all just upgraded from the 2010 evo to 2011 evo 290cc 2011 was few month old when i got it and have noticed (1st time out on it today) that when am riding it feels asif you have a puncture in front tyre?? front end feels stiff when riding also when had it stood in garage was stood few days moved handlebars and was asif it was sized up in head stock? has anyone had any problems similar ???

Just got a couple of splash guards for the new Beta.They fit perfectly and look to do the part.Ordered from sxs and where here in a week.Just wanted to say good service and parts.JR

Does anyone have any idea how to seperate a beta techno 1999 crank so I can put new piston rod bearings

I just started my bike after about a year stood still started no worries, but got a knocking noise ? Changed piston rings and top bearing but still makes same noise any ideas what next ? Or any one recommend a good shop for rebuild thanks

can anyone tell me if the tr32/34 has 3 wires from stator to cdi 1 blue 1 black and 1 grey ,if so what cdi does it use

Hey guys, My beta 2008 beta Rev 3 270cc has started making quite a loud knocking noise from the engine it's sounds like it's coming from the top end. Also when I've removed to spark plug it has a black, wet (sort of oily) residue on the plug I don't know if this has anything to do with the noise but I know the spark plug shouldn't look like that. Anybody got an idea what the problem(s) are? Thank you in advance Jordan

Anyone know where I can get some bolts for my fan?

Hi All I am trying to track down a fuel leak from the tank area. How does the little plastic tank cover get removed? I have tried prying it off, but am worried about breaking it. Cheers

Hi I have an 11 Evo 290. When using the mapping on the more subtle setting the bike seems to be pinking inthe lower gears. I what can I do?