Jump to content

robido

Site Supporter
 View Profile  See their activity

  • Posts

    90

  • Joined

  • Last visited

 Content Type 

Everything posted by robido
 
 
  1. robido

    Lockdown spending

    robido replied to daveraw70s's topic in OSSA

    Nice looking bikes. Have you got hfs setup in the forks if so how do you like them and which one. Cheers
  2. robido
    Try in motion. Bultaco uk
  3. robido

    Wheel building.

    robido replied to colinf's topic in Bultaco

    Just stripped my front wheel down to respoke with stainless and measured my offset at 12.5mm from brake side so it could be 15mm is correct . Mines a 199a. Hope this helps
  4. robido
    Where did it all go wrong. What happens to proper trials
  5. robido
    Splat shop have kits for 1999 to 2013. Give Chris a ring
  6. robido

    Cub Clutch woes

    robido replied to wezzo's topic in Pre-65 Bikes

    Plates will be ok they can run dry as do Pete's clutch. You won't regret buying one. Fit and forget I don't bother using a gasket as no oil to leak.
  7. robido

    Cub Clutch woes

    robido replied to wezzo's topic in Pre-65 Bikes

    Pete Kirby 07886 745942. Nice chap very helpful. Not cheap but quality never is. I've had 3 from him work nice. Think they were about £450.
  8. robido

    Cub Clutch woes

    robido replied to wezzo's topic in Pre-65 Bikes

    Get A Pete Kirby belt drive clutch no oil work brilliant. You won't regret it
  9. robido

    Baldyjohn

    robido replied to Baldyjohn's topic in Pre-65 Bikes

    Ebay. Or you can buy direct from Rupert ratio site
  10. robido
    Terry weedy does a nice one. Look at his web site
  11. robido
    That sounds like a bargain at that price. Room for some upgrades like Whitton alloy hubs and still be a cheap bike
  12. robido

    Gas gas 250

    robido replied to Tom_H123's topic in Gas Gas

    Whiskerd plug
  13. robido
    Wrong engine for comerfords cub it should be points on side not dizzy engine
  14. robido

    Engine Paint

    robido replied to tyguy's topic in Yamaha

    I use rustoleum bbq paint. Stays on and looks good. Got it on Amazon
  15. robido
    The ag bikes alloy swing arm is a copy of a works bike. Ag has the actual bike in his collection. Ag bikes are located in north yorkshire uk
  16. robido
    Yes you should be able to tell. There will be a close fitting washer on the crank which if you remove it you will see the rollers cage behind it. The washer is a precision fit inside the bearing outer as it keeps the oil in. Hope this helps
  17. robido
    Sounds like a blockage and not circulating
  18. robido
    I have 2 engines with the Pete Kirby belt drive clutch. Money well spent. Nice and progressive no slip no oil to leak don't need a gasket. Fit and forget. I also have a alloy one from Burton's its better than a standard one and a lot lighter but nowhere near as good as the Kirby clutch.
  19. robido
    AG bikes in the UK do an alloy one
  20. robido
    62 here and bouncing not to bad. Made a return after about 30 years things have changed a lot
  21. robido

    BSA Frame

    robido replied to pocket's topic in Pre-65 Bikes

    Don't know who built that but Jim pickering does the Drayton c15 frame Really nice and well made at a good price
  22. robido
    Try bob at upb
  23. robido
    Honda mtx 125/200 looks the same
  24. robido
    Why not make the Scott a world round. Now that's a trial
  25. robido
    I use a garmin edge GPS cycle computer. no wires works great. Have two mounts so I can swap back to mtb easily. Got it on line cheap as new model had come out
 
×
  • Create New...