baldilocks

also if you fit Ti footrest brackets you will bend the frame rather than the footrest bracket. Seen a couple of people break the frames in that area.

erm no not really an air cooled yam mono will have a number of problems at a pre 65 trial I would think..... or are you kidding ?

unfortunately for Pidcocks he is going to prove of the long standing truths in trials. A good rider can make any bike look good. I of course will be demonstrating the opposite, a bad rider cant make a good bike look good......

yes you can get the team gear from MRS it made by Clice, Jisie are doing some cabestany replica stuff but its not out for a couple of months yet.

something doesnt sound right here. Boyesen Reeds tend to make the bike run lean on the pilot, so on my 07 290 when I fitted them i had to go up a size on the pilot jet. So your bike Chewy should, all other things being equal, be running weaker than mine with std reeds. I have a 36 pilot at 2.5 turns out and your running 35 at 1.5 with the boyesen reeds? why is your bike not pinking ?

Copey me thinks you have a somewhat hotter / drier climate than the UK as you will discover shortly at the ssdt...... 36 pilot and the mixture screw is 2.5 turns out, think thats about in the middle. If I go to a 38 then the bike will be too rich on a damp day at my favourite event ! Damp days are fairly common at this particular trial

or ring wayne sherco 290 for sale, not used for last 3 years due spending all my time on the web !! If hes getting arm pump its the beginning of the end..... I have been trying for ten years to balance my bike on the back wheel intentionally and failed. El Maestro changes gear balanced on the back wheel balanced on a rock. I HATE HIM!!!!!!

My 2011 250 came with a 35 pilot jet but the mixture screw was 4 turns out to stop it pinking so I have fitted a 36 which means I have a bit more adjustment left. I think this helps as its got more off the bottom now its not too weak. other things you could try are Boysen Reeds as they helped smooth my 290 a few years ago and are not too expensive, get the, from motomerlin assuming the design hasnt changed. first thing to do though is retard the timing as it costs nothing and can be changed back if you dont like it. I havent retarded mine as my last bike was a 300 Gasser so i'm very happy with the 250 as is but it may help you.

I used MSM for my new bike insurance and it was as Scoobydo described. I find MSM good to deal with and its a proper trial policy so you are covered if you have a bump during a trial. spot on !

I'd push it, its their responsibility to know what it is they are actually selling.

Ditch two of your three tyre levers and the gloves and jacket. trials tyres are easy to fit, to remove you can use the end of a spanner and one tyre lever,remember you will only be removing a front tyre on the course if its punctures already so dont worry about the tube. You only need one tyre lever to refit a tyre, you can stop it sliding with your knees. Spare gloves might seem like a good idea but if its raining proper ssdt rain its pointless as by the time you put them on they will be as wet as the ones you have just taken off Finally dont ever leave the parc ferme without wearing your jacket, the weather changes fast so I would wear it rather than carry it.

Grip is affected by a number of variables on a bike these days you can get lots of aftermarket products like footrests and bar clamps which can be higher/lower/further back/further forward than std. Then the owner of any bike can adjust suspension, carb jetting, ignition timing, bar position, lever position etc. all of these things can effect grip as they effect how you stand on the bike or how the power is delivered compared to you twisting the throttle. Its very difficult to compare two bikes as no two bikes are the same. if you find it hard to get grip with focus on standing further back and being smoother with the throttle. Fit a slow throttle if it doesnt have one already then come back and we can all chip in with other things to change if you wish.

yes I've added an in line petrol tap to mine so I can turn the petrol off when I clean the carb. cost a

I think it is Bernies old bike you can tell by the factory lightweight rear mudguard !

so Map 2 is only the softest, as in less power per rpm on two of the 3 maps but the change is probably marginal looking at the graph until you get way beyond what I'll ever rev it to. Chris do you know which of the 3 applies to the 2011 bike out of interest ? its a good point though Chewy, why not change it at 3000 rpm, I doubt cabestany ever gets to 10,000 never mind Joe Public.

Hi folks have searched the sherco forum and found contradictory answers to this question. On the 2011 sherco which setting advances the timing map 1 or 2 ? its still a relatively new bike so i dont want to rev to a few thou rpm to test myself and its not in the manual. cheers

Good engine in those bikes. Ignition timing can be adjusted by fitting a different chip under the seat, blue is std grey is advanced from memory. Not sure if you can adjust the timing at the stator as I never took the flywheel off mine. I used fuel mix of 50 to 1 but oil is a bit better now so you may get away with 60 or 70 to 1. enjoy

This is just theory but in my 280 and 300 pros I fitted a 1mm base gasket as this more reliable and calms down the power delivery, even going 0.8 to 1mm you can tell the difference. 1mm is more reliable as the bikes often come with a 0.5mm base gasket which the bigger engines can blow at the edge of the cutaway for the transfer port. Now I suspect that 2.4mm of base gasket is way to much and i'm wondering if this also has the effect of making the engine run hotter as you should have more unburnt fuel. As the combustion area at TDC is now compartively much bigger the fuel wont be as compressed when it ignites perhaps leaving more unburnt? retarding the timing also makes an engine run hotter. The combination of these two may well be your issue. A 300 is quick but I found with mine that it was actually harder to ride with a low compression head insert.So you may find a 1mm gasket, slow throttle and a flywheel weight gets you there. Lots of VERY good riders run a flywheel weight and my theory was if they need one I'm only kidding myself if I think I dont. Let us know how you get on.

I have the same problem being between sizes so last time I got the larger one then took some padding out of an MTB lid and taped it under the liner. Maybe not ideal but better than removing my ears when I remove my lid.

Jack Challoner has done a great job in his first year. As somebody else pointed out recently everyone else bar Jack has been at the top since before the Bou era commenced, as raga,cabestany, fajardo and fuji get older it becomes less likely they will beat Bou. So logically it needs to be either Jack or somebody else new to the top class. anyone think within two years somebody will emerge to topple Bou ? if not Dougies record may not last, its not that long ago I never thought somebody could do 7 years consecutive as World Champ again.

Have a look on splatshop they will probably have the parts in stock. I'd flush the engine through now with some cheap oil to make sure you got all the coolant out.

Donald really you protest too much. the one piece made its debut in the 2006 ssdt, but that was before I went onto the intensive pie diet.

just a friendly tip really. My first ssdt I was three numbers front of my dads supported rider, John Reynolds. Beforehand I thought I 'd be able to ride around with him and learn from his experience. Mondays first sections were on the Ben with a couple of miles of off road to get there. JR passed me before we got to the sections and was riding the first one as I got there. I panicked thinking i'm going far too slow but I cant ride much faster than this. I just hadnt appreciated how quick the good guys are and there was no need to panic. If the guys in this thread are first timers I just want them to realise beforehand that Dibs being quicker than them isnt a big deal if it happens, its only a problem when everyone leaves you for dead. In my experience the top guys are happy to give advice if your at a section when they are.

I think this is more about the locations ability to subsidise ossa. ie if they stay put no euro grant, if they move free new factory ?

Every morning the two newcombers will see dibs in the parc ferme. Dibs will run up section one and be gone while the two new guys discuss yesterday. Dont let the fact dibs is near you put you off, the top guys are so quick you wont see much of him anyway. Just enjoy the ssdt for what it is, the best trial in the world !