Bultaco

1,794 topics in this forum

1. Crank shaft seals

   By rileys, February 13, 2021
   • 4 replies
   • 2k views
   • 
   • bullylover
   • February 16, 2021
2. 
   

3. Crank Thrust Washers

   By sadlotus, August 17, 2012
   • 14 replies
   • 7.4k views
   • 
   • 325
   • August 28, 2012

4. crank weight nut

   By bondy, August 18, 2011
   • 2 replies
   • 2.4k views
   • 
   • bondy
   • August 19, 2011

5. Crankcase Reassembly ?

   By netley, October 20, 2016
   • 3 replies
   • 2.1k views
   • 
   • twinnshock
   • October 21, 2016

6. Crankcase welding

   By jojotut, July 27, 2017
   • 6 replies
   • 2.6k views
   • 
   • gii
   • July 28, 2017

7. Crankshaft bearings , where did they go?

   By dr-alpina, April 11, 2019
   • 4 replies
   • 2.3k views
   • 
   • peterb
   • April 11, 2019

8. Crankshaft rebuild

   By myson, December 29, 2010
   • 5 replies
   • 3.6k views
   • 
   • monty_jon
   • December 29, 2010

9. Crankshaft Update 350t

   By brt650, September 10, 2009
   • 11 replies
   • 4.5k views
   • 
   • brt650
   • December 12, 2009

10. Custom modernized Bultaco

    By scot taco, December 22, 2018
    • 9 replies
    • 5.1k views
    • 
    • model80
    • December 30, 2018

11. Cutting Off Frame Tubes Under Engine On A 159 ? 1 2

    By paxo, February 19, 2013
    • 17 replies
    • 5.4k views
    • 
    • sherpa325
    • February 23, 2013

12. Cyl Head Gasket

    By paulmac, February 12, 2012
    • 11 replies
    • 6.4k views
    • 
    • paulmac
    • February 20, 2012

13. cylinder head nut and bolt touqe

    By bondy, July 26, 2011
    • 3 replies
    • 5.9k views
    • 
    • bondy
    • July 27, 2011

14. Cylinder Head Torque Settin

    By bondy, October 5, 2012
    • 6 replies
    • 5.6k views
    • 
    • bondy
    • October 7, 2012

15. Cylinder Heads.

    By bulltaco340, August 26, 2014
    • 6 replies
    • 3k views
    • 
    • bulltaco340
    • August 28, 2014

16. Cylinder re-sleeve

    By Cribbs74, October 11, 2018
    • 10 replies
    • 5.2k views
    • 
    • Cribbs74
    • October 12, 2018

17. Daft question time!

    By colinf, June 17, 2021
    • 3 replies
    • 2k views
    • 
    • model80
    • June 21, 2021

18. Damper rod jammed

    By ewyasrover, July 18, 2020
    • 7 replies
    • 2.8k views
    • 
    • ewyasrover
    • July 26, 2020

19. Decompresor

    By bondy, March 14, 2012
    • 5 replies
    • 2.3k views
    • 
    • keychange
    • March 15, 2012

20. Decompressor Position

    By mur, May 27, 2013
    • 3 replies
    • 1.9k views
    • 
    • mur
    • May 28, 2013

21. Default Amal Carb Settings - Model 150 250Cc Sherpa

    By max, November 13, 2012
    • 3 replies
    • 3.3k views
    • 
    • bondy
    • November 14, 2012