Everything posted by lemur
-
2012 Explorer 280i Rebuild
That's 5 micron 🤔 it takes some serious optical equipment to measure in microns considering the human eye can only see something 8 times that size.
-
2012 Explorer 280i Rebuild
Conrod has zero play, I'd roll with it. It will likely engine knock a little like an OSSA 🍀
-
Montesa 4 Ride Oil Filtration Issues
Online manuals are easy but thank-you. Document the heck out of that part if you are going for a new engine, hopefully that happens. I'd be most worried about heat near the exhaust valves and would be inclined to take pictures of inside the top end.
-
Piston knock on 301rr?
Check that your oil delivery hole is not plugged, possibly even since new, somebody just now reported that issue on a 4-ride, & that would certainly account for an engine knock.
-
Montesa 4 Ride Oil Filtration Issues
You got a part number for that shell bearing? 🤔 I think the oil pressure is mostly top end and you haven't experienced problems yet because it's built really well and the oil in the wet sump and splash off the cam chain was sufficient to stop it from imploding.
-
Tire Studs
Snow was too deep to ride for a couple of weeks but conditions are improving 👍 at least I can ride the lake and the snowmobile tracks now, just wish I had made way more tracks. If you're planning on riding winter trails where there is snow accumulation figure on needing a trail groomer or two.
-
Em
Hey Emlyn, I had one of those once, had to rewind the alternator coils when it burned out. The 12 volt rectifier you need is nothing special you can use one from almost any similar motorcycle, same with your rear brake master cylinder, should not be difficult to source either of those items. Worst feature of the bike is the air intake doesn't like deep water crossings, that's what eventually killed mine, try not to drown it.
-
Brake drums
Made a set of custom brake shoes for a friend that rode one of those, I used Thorndon XL elastomeric bearing plastic and it made the front brake powerful enough to do nose wheelies, unless you run them hot enough to melt the plastic, that was not so good 😆 Not saying I would recommend that exact modification unless you regularly ride in deep water, but it's worth mentioning that there is another way to approach the problem 🤔
-
Fantic 249r 1994 clutch
Using mineral oil for any hydraulic application that won't end up oiling your brake pads is a brilliant move. To minimize the number of fluids that you use for maintenance buy Honing or Sharpening Stone Oil which is food safe mineral oil and excellent for lubricating anything that needs a light oil. Norton brand is what I've used for decades in all kinds of applications and it costs ~20$ per quart which will last you almost a life time if you only use it on your motorcycles.
-
Bultaco Sherpa T 350 1973
You can do like I do and continuously ride the rear brake 😆 hard on the brake pads but at least you never lose track of where the brake pedal is.
-
250 Beta 250 EVO - Amsoil Saber
The big difference between Saber and Dominator or Interceptor is that Saber 100:1 oil is too concentrated to use in an oil injection system.
-
250 Beta 250 EVO - Amsoil Saber
I have used Saber in everything 2-stroke for many years with no issue.
-
Newbie
Buy something built in this century and fitted with 4 piston front brake, 2 piston rear brake and most important it needs to start easy. For gear you will want an open face helmet, gloves, proper trials riding boots and a back protector is recommended or required once you plan to ride in competitions. To advance your riding skills fast you will want riding partners, ideally someone riding at a higher level than yourself that you can follow, plus a venue that features some challenging natural terrain. Trials bikes are among the most expensive motorcycle per pound you will ever buy but cost of operation is relatively low, they don't break easy and they burn relatively little fuel, however replacement parts like fenders and tires will be expensive. If buying used, plan on spend almost as much time servicing your motorcycle as riding it.
-
Piston knock on 301rr?
Too new to expect serious problems, I would check the plug gap or replace the plug, check the air filter for cleanliness and the correct saturation of filter oil, basically anything that would cause fuel to incompletely ignite in the combustion chamber such as the ignition timing.
-
Montesa 4 Ride Oil Filtration Issues
On the up side the 4RT engine is designed to survive low oil pressure far better than a regular Honda engine costing near half as much, there are roller bearings instead of oil pressure bearings or on near everything.
-
Montesa 4 Ride Oil Filtration Issues
If the Oil Strainer Screen is plugged the pump and filter will starve. I didn't see mention of the strainer screen outside of the Engine Oil Flow Chart pictured above.
-
348 Gear box problem?
Need a better description but if it shifts through every gear and the lever springs back to centre after shifting, you likely have it together right, how well everything slides is dependent on how careful you were on assembling all the sliding parts and condition of the shifter forks, bent or worn shift forks will cause imperfect movement of the spur gears but you should notice that on disassembly or by the metal shavings in the oil changes. What was the condition of the shifter forks when it was apart?
-
Wiring diagram
You can get more from just looking at the parts diagrams. Twin map on a carburetor bike is just an ignition retard or advance, not much more it can be.
-
Montesa engine number
I think you are looking at a 1978 or 1979 360 Enduro 👍 sweet bike, I bought a 66M in 1976 but that is the 360VA Motocross version 👍 awesome bike, wish you had an engine for that one, I'd buy one of those in a heartbeat.
-
Wheel spokes front?rear
If all else fails; Zinc plating is the easiest electroplating that you can do yourself with very little cost or equipment.
-
Gas gas txt boy 50
GasGas parts manual on bike-parts-gasgas lists the fan for the 2005 TX50 as part BT720003013. and that is the same part number as a KTM and Husqvarna fan, but they say contact them to order because I suspect they are going to tell you the entire stator and magnet need to be replaced as well. The fan runs off DC so there is a small rectifier on there to convert the AC coming off the existing alternator, if I was you I would start by testing the voltage output from your rectifier and then you can source a small muffin fan to suit the voltage and mounting space. Muffin fan is what they were originally called and they are available in a vast range of sizes, muffin fan power requirements start at 5VDC which is USB standard and if your alternator can't power the fan you could add a rechargeable battery to run the fan dead loss and recharge it when you're not riding.
-
TLM 260
Other than a slight bend in profile and being bolted more rearward on the swing-arm, that side stand looks very close to a stock 4RT side stand.
-
Throttle Cable Issues
Yes to that, all the way back to 1970' twin shock bikes I had throttle cable kink issues that became a problem, but I never had to replace a throttle cable on any of my 4RT rides because I wrapped the cable as soon as I bought one. I do the same thing with my TRS bikes now, although the TRS throttle cable has less tendency to kink the shield at the connections and only needs covering on one end of the cable slack adjuster.
-
Throttle Cable Issues
I always wrapped that part with the spiral plastic that you use to bundle electric wires together, put it on before the cable is too badly kinked and it works great. Search 'spiral wire wrap'
-
Dmv No Likey My Vin #
The VIN bombs the gasgas VIN test, but EC200 would make it an enduro bike manufactured somewhere between 2004 and 2007 Best to start a new thread for this unless you are also wanting to plate it in California where the chances of that are slim to nil.