Vertigo
216 topics in this forum
-
Hi guys, was my first outing today on the vertigo r2 250cc 2020 model. First owner...ive noticed sometimes more than other takes about 10 kicks to start when hot? Is there a knack to starting throttle positions? Any help be great, I will obviously call dealer also
-
-
- 10 replies
- 6.1k views
- 1 follower
-
-
I did some searching, but didn’t see any answer. Is there any sort of Service Manual available for the Vertigo? software for the FI with diagnostics etc?
-
-
- 146 replies
- 43.5k views
- 3 followers
-
-
I see on Facebook a new bike coming does anyone know anymore?
-
-
- 5 replies
- 3k views
-
-
Hi, this is Ryder living in South Korea. During maintenance, I found out that the rear swing arm fixing bolt was cut off. So I want to know if I can separate the side frames. Thank you in advance. It's translated into a translator application, so I understand if there's a wrong sentence.
-
- 1 reply
- 1.9k views
-
-
Was wondering does anyone know how much oil per fork and what weight ?
-
-
- 1 reply
- 2.1k views
-
-
Riding the other day I found the clutch lever would stop before the handgrip . Still engaging and disengaging correctly I tried adjusting lever but it had shorter stroke . Cheers to mototrials west whom said check the through bolt at the centre of the clutch basket . It had wound itself out , once I chased the bolt threads it went back in and all works correctly again . Bonus is it’s a reusable gasket on the case . A small side note this is the first issue I have encountered on this 2017 vertigo 250 I bought new
-
- 1 reply
- 2.6k views
-
-
Hello, Has anyone upgraded their exhaust pipe to Titanium and wish to sell the stock unit. mine is quite dented and I would consider a used one before trying to "un-dent" it Cheers Ed
-
- 0 replies
- 1.7k views
-
-
Thinking of a new Vertigo has anyone tried the new 280?
-
-
- 9 replies
- 3.9k views
-
-
Are the countershaft and rear sprockets specific to Vertigo, or are there generic options available for one or both?
-
-
- 2 replies
- 2k views
- 1 follower
-
-
Not long purchased my 2020 vertical 250 and noticed it does not like pull from very low revs as the engine seems to bog down and rattle like its got a lean ping. anything above that its clean as a whistle right up to full throttle. Do I need to get access to a tuning box and enrich the mixture of the bottom to eliminate this? Another thing I have noticed is the tick over has gone up of late,, it now idles much higher than it did previously but I haven't changed anything. Can I just turn the tickover down at the screw on the throttle body? Many thanks in advance for any advice.
-
-
- 10 replies
- 5.1k views
-
-
Hi guys, has anyone removed their swing arm? Do I need an extractor to remove the anodised red semi axis?
-
- 1 reply
- 2.5k views
-
-
Hi guys I’ve recently had a 2017 ice hell, I was just wondering what the sag is like on your bike guys? bike on paddock stand rear wheel off the deck I can lift the rear wheel a few inches but the motion feels very loose like a bolt has snapped or the sleeves in the linkage by rear shock have worn, anyone else noticed this?
-
- 0 replies
- 1.5k views
-
-
Hi all I'm after a new chain for my 250 ice hell the only place I seem to find one is Vertigo uk as mine is a 103 link. Does anyone know where else I could get one or any other Ideas Thanks
-
-
- 4 replies
- 2.8k views
-
-
Sold my ‘17 Montesa 4rt and bought a left over ‘19 Vertical Combat. I love this bike! So much easier to ride in all respects... except one, starting. If I have a tree to lean against or a rock to stand on where I can get up over the bike, I can start it 1st or 2nd kick. But if none of those available no way. What am I doing wrong? How do I position my body to get enough leverage to kick it over????? i tried using the side stand to support the bike while that worked, it bends the side stand.
-
-
- 22 replies
- 12.2k views
-
-
Evening, I’m planning on greasing and checking my rear suspension this weekend and it’s a while since I’ve done one, has one got any advice as to what order I strip it all down in ????
-
-
- 4 replies
- 3.6k views
-
-
hi.... I'm jeong won living in South Korea. Vertigo 12v start battery connection is inconvenient So I made a 12v portable starter battery with 18650 batteries. It is 11.1v by connecting three 3.7v batteries, but 12v comes out because it is 4 volts when fully charged. In the photo, the battery hold is on the side but is actually under the air filter. Make a switch and start the engine When started, disconnect the switch. If the switch is connected and kickstarter 3 starts.
-
-
- 4 replies
- 4.7k views
-
-
-
Hi. The Vertigo user lives in South Korea. This time, I'm trying to buy a 9v high battery, so I don't have much in South Korea. It takes a long time to purchase from Ali Express. So I made a 9v replacement battery with aaa rechargeable batter. the charge is good, up to 9vIf
-
- 1 reply
- 2.7k views
-
-
hi. The startup problem was well resolved via the forum. Mister peterb Thank you again. This question is 9v battery capacity question. I need to use a 9v rechargeable battery Can I charge my battery while starting up? And 9v rechargeable battery capacity How much should I use? at Least 200mah? 250mah? Can I use 1000mah? (16 Vertigo Combat 300 )
-
- 4 replies
- 2.2k views
-
-
Hi what are the vertigo bikes like to ride and reliability I’m not after one at the min just curious as never seen one in the flesh
-
-
- 1 reply
- 2.2k views
-